What Are Voltage Sags and Swells? Causes, Effects, and Testing Methods

Learn the causes and effects of voltage sags and swells, how to detect voltage disturbances, and how power quality analyzers help troubleshoot them.

Voltage sags and swells are common power quality problems in industrial and commercial electrical systems. A voltage sag is a short drop in RMS voltage, while a voltage swell is a short increase above the normal level.

Both events can affect sensitive electrical equipment, interrupt production, and cause unexpected shutdowns. Understanding their causes and learning how to detect them helps engineers find problems before they lead to equipment failure.

What Are Voltage Sags and Swells?

A voltage sag occurs when the RMS voltage drops below its normal value for a short period. A voltage swell occurs when the RMS voltage rises above its normal value.

IEEE 1159 classifies these events by voltage magnitude and duration. A typical short-duration sag falls to 10%–90% of the nominal voltage, while a swell rises to approximately 110%–180%. Both can last from half a cycle to one minute, depending on the event category.
References: IEEE 1159

Event Voltage Level Typical Duration
Voltage sag 0.1–0.9 pu 0.5 cycle–1 minute
Voltage swell 1.1–1.8 pu 0.5 cycle–1 minute

Here, pu means per unit. A value of 1.0 pu represents 100% of the nominal voltage.

For example, in a 230 V system:

  • 0.8 pu = 184 V
  • 1.0 pu = 230 V
  • 1.2 pu = 276 V

A voltage sag to 0.8 pu means the voltage has dropped to 80% of its nominal value.

What Causes Voltage Sags?

Voltage sags often occur when electrical loads draw a large current or when faults affect the power supply network.

Common causes include:

1. Short circuits

A short circuit on a feeder or nearby electrical circuit can cause a sudden voltage drop. The fault current creates a voltage drop across the impedance of the supply network.

2. Large motor starting

Large induction motors can draw several times their rated current during startup. This high starting current may cause a temporary voltage drop, especially in systems with limited supply capacity.

3. Heavy load switching

When large industrial machines, compressors, or pumps start, their sudden power demand can reduce the supply voltage.

4. Utility network faults

Faults on transmission or distribution lines can affect voltage at multiple locations. Even when a fault occurs far from a facility, the connected equipment may experience a voltage sag.

What Causes Voltage Swells?

Voltage swells occur when the supply voltage rises above its normal level. They often result from sudden load changes or problems in voltage regulation.

Common causes include:

1. Sudden disconnection of large loads

When a large load switches off, the system voltage may rise temporarily because the electrical demand decreases.

2. Single-phase faults

In some three-phase systems, a ground fault on one phase can cause voltage increases on the other phases, depending on the grounding arrangement.

3. Incorrect voltage regulation

Improper transformer tap settings or regulator operation can cause excessive voltage.

4. Capacitor bank switching

Switching capacitor banks can produce voltage changes and switching transients. The actual effect depends on the system configuration and switching conditions.

What Is the Difference Between Voltage Sag, Swell, and Interruption?

These three events describe different types of voltage variation.

Event Main Characteristic Typical Effect
Voltage sag Short-term voltage decrease Equipment may slow down, reset, or trip
Voltage swell Short-term voltage increase Insulation and electronic components may experience extra electrical stress
Voltage interruption Supply voltage drops close to zero Equipment may stop operating

A voltage interruption is more severe than a typical sag because the supply is almost completely lost.

Engineers should also distinguish short-duration sags and swells from sustained undervoltage and overvoltage. A voltage condition lasting longer than one minute is generally classified as a long-duration variation rather than a short-duration event.

How Do Voltage Sags and Swells Affect Electrical Equipment?

The effects depend on event magnitude, duration, equipment design, and protection settings.

Equipment Possible Effects
PLC and control systems Unexpected reset or shutdown
Variable frequency drives Undervoltage or overvoltage trips
Electric motors Reduced torque, overheating, or contactor dropout
Industrial computers Restart or data loss
UPS systems Transfer to battery or alarm activation
Lighting systems Flickering or temporary brightness changes
Transformers Abnormal operating conditions and additional thermal stress

Sensitive electronic equipment may react to a short voltage disturbance even when other machines continue operating normally.

Repeated events can also make troubleshooting difficult. Engineers need to identify when the disturbance occurs and whether it affects one phase or the entire three-phase system.

How Can Engineers Detect Voltage Sags and Swells?

A standard multimeter can measure voltage at a specific moment, but it may miss short-duration changes. A power quality analyzer provides more useful information because it can record electrical parameters and capture waveform events, depending on its measurement functions.

A practical testing process includes the following steps:

Step 1: Check the nominal voltage

Confirm the system’s rated voltage and frequency before testing. Incorrect nominal settings can lead to misleading results.

Step 2: Connect the voltage measurement channels

Connect the analyzer according to the system configuration. For a three-phase system, measure all three phases to identify phase-specific voltage changes.

Step 3: Record voltage data

Monitor RMS voltage over a suitable period. A longer recording period helps capture intermittent events that do not occur continuously.

Step 4: Capture abnormal waveforms

Use transient waveform recording when the instrument supports it. The waveform can help engineers examine the event and understand how the voltage changed.

Step 5: Compare the results

Compare the recorded voltage magnitude and event duration with the nominal voltage and applicable power quality criteria.

Step 6: Investigate the source

Check motor starting, load switching, capacitor bank operation, protection records, and utility supply conditions around the event time.

How Can a Power Quality Analyzer Help Identify Voltage Problems?

A power quality analyzer helps engineers monitor voltage changes and investigate disturbances in electrical systems. Unlike a basic voltage meter, it can record multiple electrical parameters over time and provide additional information for troubleshooting.

The Wrindu RDCR5000 Digital Power Quality Analyzer provides:

  • Four voltage and four current measurement channels
  • Voltage and current measurement for three-phase systems
  • Transient waveform capture with up to 150 records
  • Starting current measurement with a recording period of up to 100 seconds
  • Voltage and current harmonic measurement up to the 50th order
  • Voltage and current THD measurement
  • Three-phase imbalance measurement
  • Flicker measurement
  • Data recording and alarm logging

These functions help engineers examine voltage conditions, identify abnormal operating periods, and investigate power quality problems.

For voltage sag and swell investigations, engineers should confirm the instrument’s event trigger settings, RMS measurement interval, recording duration, and event classification capabilities. Transient waveform capture should not automatically be treated as dedicated sag/swell detection.

Click the picture to learn more about the Wrindu RDCR5000 Digital Power Quality Analyzer.

How Can Engineers Reduce Voltage Sags and Swells?

The correct solution depends on the source of the disturbance.

Problem Possible Solution
Voltage sag during motor startup Use a soft starter or suitable VFD
Heavy load switching Review load sequencing and distribution
Utility supply faults Coordinate with the power utility
Sudden load disconnection Review voltage regulation and reactive power compensation
Incorrect transformer voltage Check transformer tap settings
Capacitor switching disturbances Review capacitor bank switching and protection

Engineers should identify the actual cause before selecting corrective equipment. Installing a voltage regulator or other compensation device without understanding the disturbance may not solve the underlying problem.

Frequently Asked Questions About Voltage Sags and Swells

Are voltage sags more common than voltage swells?

Voltage sags are commonly associated with short circuits, motor starting, and heavy load changes. Swells can occur during load disconnection, ground faults, and voltage regulation problems. Their frequency depends on the electrical network and connected loads.

Can a voltage sag damage a motor?

A short voltage sag may reduce motor torque and increase current demand. Repeated or prolonged disturbances can contribute to overheating or cause protective devices to trip. The actual effect depends on the motor design and operating conditions.

Can a multimeter detect voltage sags?

A standard multimeter may show a voltage drop if it occurs during the measurement, but it can miss short events. A power quality analyzer with suitable recording and event measurement functions is more appropriate for investigating intermittent voltage disturbances.

What is the difference between a voltage sag and undervoltage?

A voltage sag is a short-duration decrease in RMS voltage, generally lasting from half a cycle to one minute. Undervoltage is a long-duration voltage decrease that lasts longer than one minute under the IEEE 1159 classification.

How long should engineers monitor voltage quality?

The monitoring period depends on how often the problem occurs. If voltage disturbances happen during specific machine operations, record data during those operating periods. For intermittent problems, longer monitoring may be necessary to capture enough events for analysis.

Conclusion

Voltage sags and swells can affect industrial equipment, control systems, and production reliability. Engineers should check both voltage magnitude and event duration to understand the severity of each disturbance.

A power quality analyzer helps record electrical conditions and investigate abnormal voltage behavior. Regular monitoring, combined with a clear troubleshooting process, makes it easier to identify disturbance sources and select suitable corrective measures.

wrindu
wrindu